Z-microsystems 15 Manuel d'utilisateur

Doc# 27-0002UM Issued 7/99 Rev. 1.2Z MicrosystemsFIELD-READYCOMMANDCONSOLE15Z MicrosystemsFIELD-READYUser Manual

Doc# 27-0002UM Issued 7/99 Rev. 1.2Loosen the screws oneach of the front Z-Lockmounts.FINAL ADJUSTMENTS OF THE COMMAND CONSOLESlide the Console

Doc# 27-0002UM Issued 7/99 Rev. 1.2Close the storage traytop, then place thekeyboard and mouse ontop of the tray door.Using both hands,gently lift

Doc# 27-0002UM Issued 7/99 Rev. 1.2Place the keyboard andmouse inside the trayalong with all cablesand close door.Using both hands,gently drop the

Doc# 27-0002UM Issued 7/99 Rev. 1.2POWERING UPOperation4 cables connect the back of theConsole to the computer. Power cable Video cable Keybo

Doc# 27-0002UM Issued 7/99 Rev. 1.2Configure MonitorThe Command Console offers several methods to set up the monitor, depend-ing on the operating sy

Doc# 27-0002UM Issued 7/99 Rev. 1.2NOTE: After making changes inthe Setup, the computermust be Rebooted toinsure proper changes tothe CONFIG.S

Doc# 27-0002UM Issued 7/99 Rev. 1.2AUTO SETUP FOR WINDOWS 3.1, 95, 98 OR NT1. Turn the monitor on first, then thecomputer. If the message CH

Doc# 27-0002UM Issued 7/99 Rev. 1.27. Use an Arrow button ( ) toselect the Image Lock icon (symbolof Image Lock) and press OSDEnter button to acces

Doc# 27-0002UM Issued 7/99 Rev. 1.2Monitor AdjustmentsMaking adjustments to the Command Console screen is a matter of perform-ing the following easy

Doc# 27-0002UM Issued 7/99 Rev. 1.2OSD Lock/Unlock This feature allows you to securethe current control settings, whileallowing the user to adjust

Doc# 27-0002UM Issued 7/99 Rev. 1.21. Use the powerand videocables suppliedwith theCommandConsole to helppreventinterferencewith radio andtelevision

Doc# 27-0002UM Issued 7/99 Rev. 1.2Monitor AdjustmentsInitial Appearance of OSDOSD Functions20

Doc# 27-0002UM Issued 7/99 Rev. 1.2OSD FunctionsMonitor Adjustments21

Doc# 27-0002UM Issued 7/99 Rev. 1.2OSD FunctionsMonitor Adjustments22

Doc# 27-0002UM Issued 7/99 Rev. 1.2• Gently wipe the covers and the screen with a soft cloth.• Remove finger marks and grease with a damp cl

Doc# 27-0002UM Issued 7/99 Rev. 1.2TroubleshootingNOTE: For image problems, youmay want to run AUTOSETUP again beforeconsulting to this section

Doc# 27-0002UM Issued 7/99 Rev. 1.225Troubleshooting

Doc# 27-0002UM Issued 7/99 Rev. 1.2The display mode the monitor uses iscontrolled by the computer. Refer tothe computer documentation fordetails on

Doc# 27-0002UM Issued 7/99 Rev. 1.2POWER MANAGEMENTNOTE: If the computer haspreviously been used with aCRT monitor and iscurrently configured

Doc# 27-0002UM Issued 7/99 Rev. 1.2Display SpecificationsDisplay Type AMLCDDisplay Area Diagonal 15.0 (381 mm)Viewing Area 11.97 (304 mm) x 8.97

Doc# 27-0002UM Issued 7/99 Rev. 1.2Shock 15 G, 11 mS Operating 30 G,11mS Nonoperating Bench handingper MIL-STD-810EVibration, Random 3.0G RMS, 20-2,

Doc# 27-0002UM Issued 7/99 Rev. 1.2STARTING POINT 4Shipment Contents 4User Manual 4System Requirements 4Product Description 5PREPARATION 6INSTALL

Doc# 27-0002UM Issued 7/99 Rev. 1.2NOTE: For image problems, runAUTO SETUP again beforeconsulting this section. Inmost cases, AUTO SETUP canfix

Doc# 27-0002UM Issued 7/99 Rev. 1.2If the Z Microsystems TechnicalSupport Engineer determines that theproduct needs to be replaced, aCustomer Servic

Doc# 27-0002UM Issued 7/99 Rev. 1.2Z Microsystems has achieved full Y2K Compliance.In late 1997, the companys senior management assigned a Y2K Proj

Doc# 27-0002UM Issued 7/99 Rev. 1.233Drawings

Doc# 27-0002UM Issued 7/99 Rev. 1.2Drawings34

Doc# 27-0002UM Issued 7/99 Rev. 1.2Z Microsystems, Inc.5945 Pacific Center Blvd., Suite 509San Diego, CA 92121Phone: (858) 657-1000Fax; (858) 657-

Doc# 27-0002UM Issued 7/99 Rev. 1.2The User Manual comes in twoformats: printed hardcopy or CD-ROM. This Manual is also availableon the Z Microsyst

Doc# 27-0002UM Issued 7/99 Rev. 1.2PRODUCT DESCRIPTIONThe CommandConsole providesa liquid crystaldisplay, a deskwork surface andstorage for anysize

Doc# 27-0002UM Issued 7/99 Rev. 1.2TOOLS REQUIREDPRECAUTIONS Required Tools and Equipment Flathead screwdriver with about 10"shaft. Phillips

Doc# 27-0002UM Issued 7/99 Rev. 1.2SLIDE REMOVALWith the Console sittingon a workbench with thefront facing towardsyou, press down torelease the Z-

Doc# 27-0002UM Issued 7/99 Rev. 1.2Install RailsGo back on the rear ofthe cabinet frame, andtighten the slide mountto the cabinet frame.Make sure y

Doc# 27-0002UM Issued 7/99 Rev. 1.2INSTALL THE COMMAND CONSOLE IN THE SLIDESPull the two Consoleslides out until they lock.Hold the Console by